Basic Robot Building Kit For Arduino

Magnifying glass icon
  • Home
  • Shop
  • Basic Robot Building Kit For Arduino
Basic Robot Building Kit For Arduino

Basic Robot Building Kit For Arduino


Mouser No:
713-110090144
Mfr. No:
110090144
Development Boards & Kits - AVR Basic robot building kit for Arduino
Datasheet:
PDF download icon Datasheet

$55.99

Quantity

11 In Stock!

Spend another $40   to get free shipping

This kit comes with controller board UNO PLUS, AlphaBot robotic platform (line tracking, obstacle avoidance, speed measuring, IR control), and ultrasonic sensor.

While utilizing UNO PLUS as controller board, this kit is based on the Arduino software/hardware open source platform. Combined with the modular design, it's an ideal platform to get started with Arduino robot.

UNO PLUS Features

UNO PLUS is a development board compatible with the Arduino UNO R3, an improved & enhanced alternative solution for Arduino UNO R3.

UNO PLUS Vs UNO R3:

UNO PLUS UNO R3 Remarks
Operating voltage 5V/3.3V 5V Dual voltage level to support more shields
Reset Lateral Vertical Lateral button is easier to use when connecting with shield
Bootloader switch Yes None The board can be configured to run program immediately when power-up by the switch
USB connector Micro USB USB Type B Micro connector is more commonly used, and shields won't be blocked anymore while connecting
DC jack Low profile Normal height Shields won't be blocked anymore while connecting
Power output header Yes None

Providing 5V/3.3V power output OR common-grounding with other boards

3.3V power output 800mA Max 150mA Max UNO PLUS features higher driving capability
Oscillator Crystal oscillator Ceramic resonator Crystal oscillator is suit for applications where accurate clock reference is required
ADC channel 8 6 CFG used as ADC6 by configuration, and ADC7 from the Reserved PIN
Connecting with prototype breadboard Supported Not supported Solder pads is provided for DIY interfaces to connecting with prototype breadboard
USB driver Compatible with all main systems Doesn't compatible with WIN7/WIN8 Express Edition Driver will never failed to install thanks to the onboard FT232
Firmware fixing Supported Not supported Firmware can be fixed by using the onboard FT232, no extra programmer is needed

AlphaBot Features

  • Raspberry Pi/Arduino interfaces, works with either one separately, or both
  • Arduino extend header, supports Arduino shields
  • Modular design, plug-and-play modules like line tracking, obstacle avoidance, speed measuring, etc. eliminating the trouble of connecting mess wires.
  • LM298P motor driver with diode protection circuit, more safety
  • LM2596 voltage regular, provides stable 5V power to the Raspberry Pi/Arduino
  • TLC1543 AD acquisition chip, allows the Pi to use analog sensors

  • ATMEGA328P-AU

  • AMS1117-3.3 : 3.3V voltage regulator

  • NCP1117ST50T3G : 5V voltage regulator

  • FT232RL : USB to UART convertor

  • Arduino interface

    • compatible with standard Arduino interface with two additional analog inputs A6 (config the CFG), A7
    • solder pads provided, supports prototype breadboard
  • ICSP interface
  • MICRO USB connector : for uploading program OR serial port debugging
  • Power output header : 3.3V OR 5V, voltage level configured by the onboard power configuration switch, used as power output OR common-grounding with other boards
  • FT232 pins : for burning Bootloader into the microcontroller
  • DC input : 7V ~ 12V
  • Reset button
  • Power indicator
  • Serial port Rx/Tx indicator
  • User LED
  • Power configuration switch : for configuring the operating voltage
  • Bootloader selection switch
    • turn ON : the board will reset when power-up OR other USB devices were detected connecting to the PC
    • turn OFF : the onboard program runs immediately when power-up, and the board will not reset when other USB devices were detected connecting to the PC

    1. Raspberry Pi interface: for connecting Raspberry Pi

    2. Arduino interface: for connecting Arduino

    3. Motor interface

    4. Ultrasonic module interface

    5. Servo module interface

    6. Obstacle avoidance module interface

    7. Speed measuring interface

    8. Battery holder: supports 18650 batteries

    9. Reserved power input (not soldered): for connecting other external power supply

    10. Arduino expansion header: for connecting Arduino shields

    11. UART interface: for connecting Bluetooth module, to control the robot remotely via Bluetooth

    12. SPI interface: for connecting NRF24L01 wireless module

    13. Line tracking module interface

    14. TLC1543: 10-bit AD acquisition chip, allows the Pi to use analog sensors

    15. LM298P: dual H bridge motor driver chip, up to 2A current

    16. Anti-reverse diode

    17. Power switch

    18. LM2596: 5V regulator

    19. Power indicator

    20. UART switch: turn on to enable serial communication between Raspberry Pi and Arduino

    21. IR receiver: control the robot remotely via infrared

    22. Raspberry Pi/Arduino selection: select the Raspberry Pi or Arduino to control the robot peripherals

    Note: photos are FOR REFERENCE ONLY, the other boards/modules/accessories are NOT included in the price.

    AlphaBot

    UNO_PLUS

    Package Contents Products
    Item

    Description

    AlphaBot AlphaBot-Ar-Basic AlphaBot-Ar-Bluetooth AlphaBot-Pi Acc Pack AlphaBot-Pi
    RPi3 B Raspberry Pi 3 Model B
    UNO PLUS enhanced control board, Arduino compliant
    AlphaBot chassis kit mainboard, wheels, drivers, etc.
    Tracker Sensor line tracking module
    Photo Interrupter Sensor speed measuring module (2pcs)
    Infrared Proximity Sensor obstacle avoidance module (2pcs)
    IR remote controller remotely control the robot
    SG90 servo
    Ultrasonic sensor ultrasonic obstacle avoidance, distance measuring
    Accessory Shield accessories add-on board, Arduino compliant
    Dual-mode Bluetooth dual-mode Bluetooth module
    RPi Camera (B) Raspberry Pi camera, adjustable focus
    Micro SD Card 16GB 16GB Micro SD Card, class 10
    5V 2.5A Power Adapter RPi3 B requires 2.5A or above power supply

    Note: this product requires two 18650 batteries to work, which are NOT included and should be purchased separately.

  • AlphaBot mainboard x1

  • Tracker Sensor x1

  • Photo Interrupter Sensor x2

  • Infrared Proximity Sensor x2

  • Motor with gearbox 2PCS x1

  • AlphaBot wheel 2PCS x1

  • AlphaBot acrylic chassis x1

  • Motor mounting plate 4PCS x1

  • omni-direction wheel x1

  • 20-slots encoder disk 2PCS x1

  • IR remote controller x1

  • XH2.54 4cm 4Pin 2PCS x1

  • XH2.54 4cm 3Pin 2PCS x1

  • XH2.54 4cm 7Pin x1

  • AlphaBot screws x1

  • Technical Details

    Dimensions 0mm x0mm x0mm
    Weight G.W 552g
    Battery Exclude

    ECCN/HTS

    HSCODE 9023009000
    USHSCODE 9023000000
    UPC 841454119777
    Basic Robot Building Kit For Arduino
    • Product - Robotics
    • Brand - Seeed Studio
    • Interface Type - ICSP
    • Core - AVR
    • Data Bus Width - 8 bit
    • Manufacturer - Seeed Studio
    • Operating Supply Voltage - 7 V to 12 V
    • Product Type - Development Boards & Kits - AVR
    • Standard Pack Qty - 1
    • Subcategory - Development Tools
    • Tool Is For Evaluation Of - ATmega328P